DANOTHERM : CBH, CBR Aluminium Housed Resistors
These resistors have increased nominal and overload capabilities compared to the CCH / CAH series. They are mostly used in DC-links for charging and de-charging and in medium power inverter drives systems as brake resistor. CBR has cooling fins to optimize heat transfer to the ambient air. The nominal power ranges from 85-1700W, standard maximum working voltage is 690VAC/850VDC. 1000VAC/1400VDC ty...
ABB: Varistor CR-P/M 52C/1SVR 405 653 R1000 A
Varistor is an electronic component with an electrical resistance that varies with the applied voltage. Also known as a voltage-dependent resistor (VDR).
METTLER-TOLEDO: LOAD CELL
Load cell is a type of transducer, specifically a force transducer. It converts a force such as tension, compression, pressure, or torque into an electrical signal that can be measured and standardized.
Current Transformer
Current transformer is a type of transformer that is used to reduce or multiply an alternating current.
ABB: Multifunctional Relay
Multifunctional relays are universally usable, multifunctional relay can be used as a flasher relay, clock, impulse former, start-up and/or shut-down relay as well as contact and recurrence delay.
ABB: Repair Kit 68689023
Instructed set of items for a specific ABB equipment
Chocky Bar
Anti-abrasion coating domite chocky bar
Stainless Steel Pipe Fitting
Stainless Steel Buttweld Fittings are defined as a part used in a piping system, for changing direction, branching or for change of pipe diameter, and which is mechanically joined to the system. Buttweld fittings is a butt-welded connected pipe fittings, it is easy for installation and maintenance.
Carbon Steel Pipe Fitting
Carbon steel butt-weld fitting is a weldable pipe fitting that allows for change of direction of flow, to branch off, reduce pipe size or attach auxiliary equipment. A420 = Standard specification for piping fittings of wrought carbon steel and alloy steel for low-temperature service. The ASTM A420 WPL6 pipe fitting means the butt weld pipe fittings whose material is ASTM A420 grade WPL6. ASTM A4...
Mild Steel Sheet/Plate
Wear plates are expendable items that are used to prevent excessive wear or damage to expensive equipment. Wear plate is commonly a type of abrasion resistant steel plate that is considered extremely durable, especially under harsh conditions.
Grease Fittings Imperial & Metric
Grease fitting is a metal fitting used in mechanical to feed lubricants, usually lubricating grease, into a bearing under moderate to high pressure.
Coupling
System of clutches or couplings for transmitting rotation used within a mechanism.
Carbon Steel Seamless Pipe
Carbon steel ia an alloy with carbon and iron, with carbon content up to 2.1% by weight. Seamless pipe as the name suggests is a pipe without a seam.
Pull Rope System Component
Pull Cord Switch is an emergency switch to stop the conveyor instantly in any dangerous condition or when an accident occurs.
SAE Hydraulic Flanges
SAE Flanges are made to SAE J518/ISO 6162 standards and are designed for hydraulic applications. Size Range: - SAE Code 61 flange are available in sizes ranging from (DN 10) to (DN 125). - SAE Code 62, flanges are available in sizes ranging from (DN 10) to (DN 80).
Stepper Motor Flexible Coupling
Stepper motor flexible couplings are usually used to transmit torque from one shaft to another when the two shafts are slightly misaligned. They can accommodate varying degrees of misalignment up to 1.5° and some parallel misalignment. They can also be used for vibration damping or noise reduction.
Hydraulic Fluid Filter
Filter is to remove and/or contain particles of contamination and keep the fluid that flows round the machine clear. Any contamination in the oil can cause damage to moving parts further downstream, and this can lead to seizing up of moving parts, corrosion of other parts and costly replacements.
Lubricant : ROCOL VGP compliant Wire Rope Dressing
Environmentally Considerate Wire Rope Dressing lubricant designed specifically for the following industries: Shipping ; Ports & Docks ; Dredging ; Deep Sea Fishing. VGP compliant ensuring biodegradability, minimal eco-toxicity and low bioaccumulation potential. Exhibits good penetration, this is enhanced by the use of a high pressure applicator. Leaves a thin, non-tacky film preventing b...
Water Service Valves
Valve is a device or natural object that regulates, directs or controls the flow of a fluid (gases, liquids, fluidized solids, or slurries) by opening, closing, or partially obstructing various passageways.
Hydraulic/Water Services Motor Pump- Centrifugal Type
Centrifugal pumps are used to transport fluids by the conversion of rotational kinetic energy to the hydrodynamic energy of the fluid flow.
Hydraulic/Water Services Motor Pump- Submersible Pump
Submersible pump, also called an electric submersible pump, is a pump that can be fully submerged in water, pushes water to the surface by converting rotary energy into kinetic energy into pressure energy.
HANSA-FLEX Hydraulic Pressure Hoses Reliable
HANSA-FLEX Hydraulic Pressure Hoses Reliable, high-performance hoses for industrial and mobile hydraulics. Built to handle extreme pressure, abrasion, and temperature. Available in multiple configurations (e.g., 1SN, 2SN, HD series) with steel braid or spiral reinforcement. Custom assemblies and fittings offered for precise applications.
Stainless Steel
Sockolet, Weldolet, Threadolet, Full Coupling, Half Coupling, Reducing Coupling, Elbow, Equal Tee, Cross Tee, Reducing Tee, Nipple and Union.
Grating Floor
Grating Products Durable, load-bearing surfaces made from metal. Used for flooring, walkways, platforms, and drainage covers. Available in bar, mesh, and molded styles with anti-slip features for industrial and commercial safety. - Galvanised Carbon Steel Grating Floor - Carbon steel coated with zinc (galvanised) to resist rust. - Strong and durable for heavy loads. - Used in industrial floo...
Pump Element - 600250473 Lincoln
Lincoln Pump Element with product number 600250473 is a steel pump element designed for high-pressure central lubrication systems, with a G 1/4" connection.